Today's Hours:
A fine-tip soldering iron, rosin-core solder, and isopropyl alcohol for cleaning flux residues.
The author and publisher of this article are not responsible for any damage or injury caused by incorrect connections or configuration of the KT8900 programming cable. Use this information at your own risk.
The is an incredibly popular, ultra-compact dual-band mobile transceiver prized by amateur radio operators for its small footprint and budget-friendly price point . However, programming its 200 memory channels manually using the front panel and microphone keypad can be an exhaustive, time-consuming chore.
This is the number one cause of failure. Most cheap programming cables use cloned chips.
The QYT KT8900 is a dual-mode, dual-band amateur radio transceiver that operates on both VHF and UHF frequencies. It features a compact design, a user-friendly interface, and a range of advanced features, including digital signal processing, noise reduction, and wireless connectivity. The radio is popular among amateur radio operators due to its reliability, performance, and affordability.
The Ultimate QYT KT-8900 Programming Cable Pinout Guide: DIY & Troubleshooting
Connect the ground wire from the USB adapter to the Sleeve of the 3.5mm jack.
Select the correct COM port and baud rate ( 1920019200 are common for QYT).
uses the found on the back of the radio chassis. The connector maps directly to three critical serial lines: 3.5mm Plug Section Data Signal Radio Function Tip RX (Receive Data) Data coming from the PC into the radio Ring TX (Transmit Data) Data leaving the radio out to the PC Sleeve GND (Ground) Shared electrical ground reference
: RXD (Receive Data) — Receives data from the PC into the radio.
When soldering a module like a HiLetgo CP2102 to your 3.5mm cable, cross the data lines: Solder the Tip (Radio RX) to the TXD pin of the USB board. Solder the Ring (Radio TX) to the RXD pin of the USB board.
Various diameters to insulate individual solder joints and provide strain relief. 4. Step-by-Step Assembly Instructions Step 1: Prep the Cable and Connector
Unlike many mobile radios that use an RJ-45 microphone jack or a dedicated data port for programming, the QYT KT-8900 routes its programming data through the located on the rear panel.
A fine-tip soldering iron, rosin-core solder, and isopropyl alcohol for cleaning flux residues.
The author and publisher of this article are not responsible for any damage or injury caused by incorrect connections or configuration of the KT8900 programming cable. Use this information at your own risk.
The is an incredibly popular, ultra-compact dual-band mobile transceiver prized by amateur radio operators for its small footprint and budget-friendly price point . However, programming its 200 memory channels manually using the front panel and microphone keypad can be an exhaustive, time-consuming chore.
This is the number one cause of failure. Most cheap programming cables use cloned chips. qyt kt8900 programming cable pinout top
The QYT KT8900 is a dual-mode, dual-band amateur radio transceiver that operates on both VHF and UHF frequencies. It features a compact design, a user-friendly interface, and a range of advanced features, including digital signal processing, noise reduction, and wireless connectivity. The radio is popular among amateur radio operators due to its reliability, performance, and affordability.
The Ultimate QYT KT-8900 Programming Cable Pinout Guide: DIY & Troubleshooting
Connect the ground wire from the USB adapter to the Sleeve of the 3.5mm jack. A fine-tip soldering iron, rosin-core solder, and isopropyl
Select the correct COM port and baud rate ( 1920019200 are common for QYT).
uses the found on the back of the radio chassis. The connector maps directly to three critical serial lines: 3.5mm Plug Section Data Signal Radio Function Tip RX (Receive Data) Data coming from the PC into the radio Ring TX (Transmit Data) Data leaving the radio out to the PC Sleeve GND (Ground) Shared electrical ground reference
: RXD (Receive Data) — Receives data from the PC into the radio. The is an incredibly popular, ultra-compact dual-band mobile
When soldering a module like a HiLetgo CP2102 to your 3.5mm cable, cross the data lines: Solder the Tip (Radio RX) to the TXD pin of the USB board. Solder the Ring (Radio TX) to the RXD pin of the USB board.
Various diameters to insulate individual solder joints and provide strain relief. 4. Step-by-Step Assembly Instructions Step 1: Prep the Cable and Connector
Unlike many mobile radios that use an RJ-45 microphone jack or a dedicated data port for programming, the QYT KT-8900 routes its programming data through the located on the rear panel.
GetHollow. All rights reserved. © 2026